A Nikon d3200 battery may go low and need to be recharged; then, the charger becomes unavailable. This commonly happens to those beginning to use it. It happens because they do not have an approximate time for their camera’s battery strength. Experts may also face such a problem on occasions, especially where they take too many pictures. Charging your battery without a charger is not as tough as it may seem.
In this article, I will talk about different ways which one can use to recharge a Nikon d3200 battery when a charger is not available. There are alternative ways on how to charge a Nikon d3200 battery in the absence of a charger. Of course, it is always recommended that proper equipment recharge the battery, but if the proper equipment is not available, then any option will do. This article gives you important guidelines that will highly help you put back power to your camera battery to proceed with taking photos.
Table of Contents
How to charge Nikon d3200 without its charger
DSLR cameras need too much power to operate. That is the reason why there is a limitation of shots for each make of DSLR camera. Therefore, it’s very normal for your cameras to go out of power unexpectedly. In addition, the usage of inbuilt flashes also uses the battery power very fast.
Without further ado, we shall go on the steps. I hope that as you read through the article, you will get information that will be of much help to you.
Step 1: Use of a mobile charger
A Nikon d3200 camera is packaged with the li-ion EN- EL14 battery. This means that it can be recharged. Moreover, Nikon MH- 24 charger has an 8.4V and 0.9A performance, which is the perfect charger to load.
A mobile loader also has the potential to be used. This shows the performance of the turbocharger. Its voltage is not shared with mobile chargers that are regular. They have the capability of supplying 5V. This type of battery can only get recharged by turbochargers. They can only supply 5 V.
Step 2: Use of a USB cable
A USB connection is included for charging the camera battery. Ensure that you insert the loadable battery into the camera. A portable power battery control converter or computer should be used. Click the battery lock to the arrow and insert the power pack just before the lock is complete. Hold in the battery-pack terminals. Lower the lid and hold it until the top is closed. Open the lid as long as the camera is off.
Insert the plug fully into the camera device with a smaller plugin the indicated orientation of the provided interface cable. Next, insert the bigger connection into the portable adapter or the computer’s USB terminal.
The portable power adaptor may be connected as an alternative. Loads continue, and the USB bulb lights up. The light switches off when loading is complete. Finally, remove the mobile power adapter and interface cable of the camera from the power socket.
Step 3: Use of friction
This method is more of a trick than anything else. Friction will generate heat, and a hit will provide electricity, so it’s a win-win. This might, however, not be the most productive or even the most professional way to go about it.
Nevertheless, it does work on occasion. Please remove the battery, massage it on your palm for a considerable period, and then put it back in the battery compartment. The camera may be able to be turned on once the battery has been recharged.
Step 4: Use of a battery to charge a battery
Disable the battery on the gadget. Find AA, AAA, or 9-volt batteries. You’ll need to search for both the plus and bottom connections for each battery. AA, AAA, or other batteries that are effective enough to provide the charging battery voltage.
You’ll need a double-metal cable. This is because the battery needs to be charged and that it will be better if you charge the battery for some time.
Step 5: Use of a car battery
The half amp camera battery can be switched on using three light bulbs as a regulator. Vehicle batteries and digital camera batteries have 13 volts, and, therefore, it is essential to ensure that the bulbs have 6 volts. In addition, three lights must be placed in parallel for 0.5 amps to pass through the battery. Since the bulbs are burning out, less than 0.6 amperes of power is guaranteed.
Just before your battery is fully charged enough to snap photos again, you’ll probably make a few phone calls or do some other activity. So leave it alone or charge it completely. When your camera’s battery hits 8 volts, and you charge it for too long, you may have problems. It is also possible that the camera might heat up and probably burn out.
Step 6: Use of DC Resistor Source
Ensure you find a power source for DC. Secondly, determine the voltage of your battery and use Ohm’s Law to determine the kind of resistance that flows in your batteries. This helps in discovering the resistor. Finally, a heating element such as a toaster or hair dryer may be used.
A tiny light bulb is often the best current controller. This bulb is ideal because when the filament is heated, the intensity rises, and the current decreases. And, without burning it, you can add an amp, and it acts as a fuse for you.
Use a multimeter to measure current at different voltages of your light. Do not breathe the smoke produced. It is important to wear protective gear not to cause any harm to your body.
Step 7: Modification
You have to replace it and check the precise model if the batteries do not work. Each camera model is given a battery specifically designed for that model. The manufacturer’s guarantee on each replacement battery is the greatest feature of the specific camera batteries.
The majority of digital cameras presently function on the market with a standard inbuilt battery. In an emergency, the camera battery may even be charged without a charger. Unfortunately, you cannot take a loader. In this case, you must adapt to the battery charging scenario.
Conclusion
In conclusion, it’s quite normal to have your camera off suddenly. If you are a great photographer, you are likely to carry additional batteries, and, of course, you will maintain the batteries under control. Always remember that the cameras require a lot of power to operate smoothly.
It would be best always to have an emergency battery, whether you have an inbuilt one or not. When your light abruptly stops when charging, it is most likely that the charging is complete.
If you are unsure of what steps to follow or what to do, always find an expert to help you out. Go through the instructions, and your battery will be charged for additional photography in no time. If you have followed all the above steps, and it does not work for you, refer to your manual.
If the procedures in your manuals do not help still or are not clearly stated, contact a professional with immediate effect. You can also prefer buying a charger for your Nikon battery.