Golf Cart Clicks But Wont Move – Quick Fix

Disclaimer: “As an Amazon Associate, I earn from qualifying purchases. Without Any Extra Cost to You!”

You should hear a “click” when you turn the key in your golf cart, indicating that it has started. Unfortunately, having power does not guarantee that your cart will move; several obstacles may prevent it from doing so.

A damaged battery or damage to the internal controller could cause your club vehicle to make a clicking sound but not move. Due to dust building inside the battery ports, a Club Car golf cart can start clicking but not move. These are the causes of clicking sound on the golf cart but won’t move, among others.

Here are some of the most typical issues that may be causing your cart to malfunction and ways that you can use to troubleshoot the problems.

Reasons why the golf cart will click but won’t start

golf cart will click but won’t start

1. A damaged battery or damage to the internal controller

  1. Check to see if the batteries are in good operating order.
  2. Check the batteries’ static voltage with a voltmeter.
  3. The voltages should be approximately 50 volts.
  4. If the voltage is lower than expected, it’s time to charge the batteries.
  5. Check to see whether the problem persists after the battery has been charged.
  6. The problem should go away in most cases, and you should be able to start the club car without difficulty.

The solenoid produces the clicking sound you hear. There are a variety of reasons why this might be the case.

  1. You might hear the solenoid click if the battery is dead.
  2. The solenoid may generate this sound if the wires between the solenoid and the motor are not correctly connected.
  3. If the motor or controller is destroyed, the club vehicle may not be able to move.

Examine the solenoids and the motor’s wire connections. You may hear a clicking sound from the solenoid if the wires are unplugged or broken. The problem is solved by replacing or repairing the defective cables. Your vehicle will restart.

 The solenoid may be broken or malfunctioning in some situations. You should replace the faulty or damaged solenoid with a new one and observe whether the problem still exists.

If all of the above-mentioned methods fail, you should get your club automobile inspected by a service center. The internal controller may be malfunctioning. If this is the case, the problem is resolved by replacing the controller.

2. Due to dust building inside the battery ports

dust building inside the battery ports

If you open the battery ports and look for any dust accumulation, you’ll know if this is the case. The problem is solved by adequately cleaning it with a towel. Here’s a rundown of the most common causes of clicking noises in your club car. The majority of them are simple to fix.

  1. Make that the solenoid and the battery are connected. Over time, solenoid coils are destroyed. If the solenoid is broken, replace it with an identical one and see if the problem goes away.
  2. The controller is harmed. The controller may have become obsolete after many years of use in the majority of cases. You can test the controller by removing it and putting it to the test.
  3. The car may also be unable to move ahead due to the resistance coil. The resistance values are frequently found to be outside of the typical range. To make sure the coil is working correctly, look at the resistance numbers. Replace the coil with a new one if the value is outside of the typical range.
  4. Another cause of this problem could be that the motor’s brushes have burned out. To check this, carefully open the motor and inspect the brushes for proper operation. When opening the motor, use caution. You can also take it to a service center to get it looked at.

Fixing the problem

1. Check the source of the problem

source of the problem

To fix a club car DS that clicks but does not move, you must first determine the source of the problem. The club car could be experiencing several challenges that are keeping it from moving. Before attempting to repair the problem, it’s critical to do a thorough study. Frequently, the issue will be trivial and have a straightforward cure.

The following are some of the most prevalent issues and how to solve them.

  1. Take a look at the power supply. If the battery is completely depleted, the car may make a clicking noise.
  2. A voltmeter is used to check the battery’s voltage.
  3. If the voltage is too high or too low, the battery will need to be fully recharged.
  4. Recharging the battery to its maximum capacity is a good idea.
  5. If the voltage continues to fluctuate, the battery may need to be replaced.
  6. Look for a brand and model that is similar to your club car.
  7. It’s critical to unhook and reconnect the cables properly.

Another problem could be the motor. It isn’t easy to get to the motor. After removing the motor from the cart, try to open it. There will be several minor components on the motor that you may inspect to determine if any are burned out.

Brushes are the most commonly burned-out components. You may easily replace the brushes by purchasing them from one of the cart sellers.

Check to determine if the solenoid is working correctly. If the solenoid has been damaged, it must be replaced with a new one. A solenoid coil isn’t repaired.

2. Check the MCOR connection

If the solenoid on a Club Car Precedent golf cart clicks but the golf cart does not move, make sure the MCOR connection is not loose or damaged. If you have a club car that refuses to move, it could be due to some minor internal faults that are readily rectified. Many previous owners of club cars have reported hearing a clicking sound and the car refusing to move.

You can attempt to figure out what’s causing the problem and then take the required measures to fix it.

  1. The first step is to examine the MCOR link. For any club automobile, this is critical. Ascertain that the connection is secure and that there are no loose wires.
  2. Examine the cables that link the MCOR to the various components for any damage. If any of the wires are broken, replace them with comparable ones.

3. In the controller, look for the throttle signals

A 16-pin connector is used to connect the controller to the computer. At this stage, you must look for the signals. If the signals are incorrect, the problem could be caused by the controller.

  1. The issue is resolved by replacing the controller. A controller can be obtained from any of the service locations or purchased online.
  2. When replacing the controller, you might choose a higher-quality model that performs better. The decision is based on the amount of money you want to put into your club automobile.
  3. To ensure that the battery is in good operating order, check the voltmeter reading. Recharging the battery to total capacity will sometimes cure the problem.
  4. Make that the solenoid wires and resistance coils are in good operating order.
  5. If you still can’t figure out what’s wrong, you can take it to a service center, where they can inspect the cart and figure out what’s wrong.

Conclusion

There are different reasons why the golf cart will click but won’t move. That problem might be a great stress to the owner. Luckily enough, this article discusses the problem and ways to fix it.

In conclusion, under no circumstances should you attempt to repair the golf cart on your own. Doing so is risky and could lead to significant bodily harm.

Leave a Comment